Skip to content

It is a wireless temperature, pressure and humidity sensor, supports working in Zigbee networks. (Zigbee2mqtt open source project). Built on CC2530 chip (Zigbee), two modications: Ebyte E18-MS1PA2-PCB radio module with amplifier and Ebyte E18-MS1-PCB. Powered by the most common AAA batteries.

smartboxchannel/EFEKTA-TH-THLR-Outdoor-Indoor-sensor-Zigbee

Folders and files

NameName
Last commit message
Last commit date

Latest commit

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Repository files navigation

Efekta THP_LR \ THP

Поблагодарить автора: https://www.donationalerts.com/r/efektalab

Thank the author: http://www.donationalerts.ru/r/EfektaLab

Телеграм чат DIY Devices - https://t.me/diy_devices

Продажа DIY Устройств - https://t.me/diydevmart

Option 1 - DIY outdoor/indoor long-range sensor for temperature, humidity and atmospheric pressure
Option 2 - DIY outdoor/indoor temperature, humidity and atmospheric pressure sensor, long battery life

Sale:

The cost of the device without the enclosure:

$16.5 (shtc3: temperature, humidity)
$22.5 (bme280: temperature, humidity, pressure)
+$3 Long range radio module
+$5 Enclosure
Delivery is $12.5(worldwide).
Tracknumber for tracking.
You can buy a ready-made device by writing to the mail hello@efektalab.com
Delivery is carried out worldwide.

Video:

Telegram DiyDev - https://t.me/diy_devices

More info at http://efektalab.com/eON_THP

V1_R1

Efekta THP_LR \ THP

V1_R2

(not opensource)

Efekta THP_LR \ THP

V2_R1

(not opensource)

Efekta THP_LR \ THP

Efekta THP_LR \ THP

Efekta THP_LR \ THP

Efekta THP_LR \ THP

Efekta THP_LR \ THP

Efekta THP_LR \ THP

What is it?

It is a wireless temperature, pressure and humidity sensor, supports working in Zigbee networks. (Zigbee2mqtt open source project). Built on CC2530 chip (Zigbee), two modications: Ebyte E18-MS1PA2-PCB radio module with amplifier and Ebyte E18-MS1-PCB. Powered by the most common AAA batteries. The device comes with pre-installed open source software. Supported inZ2M, ZHA

What makes it special?

RF module EBYTE E18-MS1PA2-PCB (CC2530) or Ebyte E18-MS1-PCB.

BME280 or BMP280

Long runtime with two AAA battery.

Consumption in data transmission mode ~25mA|50mA, in sleep mode 1.8μA.

How to flash the device

  1. Download the Smart RF Flash Programmer V1 https://www.ti.com/tool/FLASH-PROGRAMMER

  2. Open the application select the HEX firmware file

  3. Connect the device with wires to CCDebugger, first erase the chip, then flash it.


How to install IAR

https://github.com/ZigDevWiki/zigdevwiki.github.io/blob/main/docs/Begin/IAR_install.md

https://github.com/sigma7i/zigbee-wiki/wiki/zigbee-firmware-install (RU)

Сonfiguring the firmware before compilation

Open the preinclude.h file, select the desired configuration

//#define OUTDOOR_LONG_RANGE

//#define BMP

https://github.com/smartboxchannel/EFEKTA-THP-THPLR-Outdoor-Indoor-sensor-Zigbee/blob/9e8450923bca76330c3ec9616b2dffed900a4576/PROJECT%20SOURCE/THP/Source/preinclude.h#L85


How to join:

If device in FN(factory new) state:

one way
  1. Open z2m, make sure that joining is prohibited
  2. Insert the battery into the device
  3. Click on the icon in z2m - allow joining (you have 180 seconds to add the device)
  4. Go to the LOGS tab
  5. Press the reset button on the device (the join procedure will begin, еhe device starts flashing the LED repeatedly)
  6. Wait, in case of successfull join, device will flash led 5 times, if join failed, device will flash led 2 times
another way
  1. Open z2m, make sure that joining is prohibited
  2. Insert the battery into the device
  3. Click on the icon in z2m - allow joining (you have 180 seconds to add the device)
  4. Go to the LOGS tab
  5. Press and hold button (1) for 2-3 seconds, until device start flashing the LED repeatedly
  6. Wait, in case of successfull join, device will flash led 5 times, if join failed, device will flash led 2 times

If device in a network:

one way
  1. Hold button (1) for 10 seconds, this will reset device to FN(factory new) status
  2. Click on the icon in z2m - allow joining (you have 180 seconds to add the device)
  3. Go to the LOGS tab
  4. Press and hold button (1) for 2-3 seconds, until device start flashing the LED repeatedly
  5. Wait, in case of successfull join, device will flash led 5 times, if join failed, device will flash led 2 times
another way

1.Find the device in the list of z2m devices and delete it by applying force remove 2. Click on the icon in z2m - allow joining (you have 180 seconds to add the device) 3. Go to the LOGS tab 4. Press the reset button on the device (the join procedure will begin, еhe device starts flashing the LED repeatedly) 5. Wait, in case of successfull join, device will flash led 5 times, if join failed, device will flash led 2 times

Efekta THP_LR \ THP

Troubleshooting

If a device does not connect to your coordinator, please try the following:

  1. Power off all routers in your network.
  2. Move the device near to your coordinator (about 1 meter). or if you cannot disable routers (for example, internal switches), you may try the following: 2.1. Disconnect an external antenna from your coordinator. 2.2. Move a device to your coordinator closely (1-3 centimeters).
  3. Power on, power on the device.
  4. Restart your coordinator (for example, restart Zigbee2MQTT if you use it).

If the device has not fully passed the join

  1. If the device is visible in the list of z2m devices, remove it by applying force remove
  2. Restart your coordinator (for example, restart Zigbee2MQTT if you use it).
  3. Click on the icon in z2m - allow joining (you have 180 seconds to add the device)
  4. Go to the LOGS tab
  5. Press and hold button (1) for 2-3 seconds, until device start flashing the LED repeatedly
  6. Wait, in case of successfull join, device will flash led 5 times, if join failed, device will flash led 2 times

Other checks

Please, ensure the following:

  1. Your power source is OK (a battery has more than 3V). You can temporarily use an external power source for testings (for example, from a debugger).
  2. The RF part of your E18 board works. You can upload another firmware to it and try to pair it with your coordinator. Or you may use another coordinator and build a separate Zigbee network for testing.
  3. Your coordinator has free slots for direct connections.
  4. You permit joining on your coordinator.
  5. Your device did not join to other opened Zigbee network. When you press and hold the button, it should flash every 3-4 seconds. It means that the device in the joining state.

About

It is a wireless temperature, pressure and humidity sensor, supports working in Zigbee networks. (Zigbee2mqtt open source project). Built on CC2530 chip (Zigbee), two modications: Ebyte E18-MS1PA2-PCB radio module with amplifier and Ebyte E18-MS1-PCB. Powered by the most common AAA batteries.

Resources

Stars

Watchers

Forks

Releases

No releases published

Packages

No packages published